QUAD EVO™ LED Driving Light

Designed as a modular system, QUAD EVO features a ‘central light’ that is equipped with 23 CREE XP20 LEDs, utilising a combination of spot + flood reflectors for optimal optical performance. Additionally, QUAD EVO is also available as a ‘side light’ consisting of 18 CREE XP20 LEDs, enhanced by 5x widespread reflectors (also known as side-shooters), which collectively provides an impressive 210-degree distribution of pure light.

IMPORTANT NOTES:

• All three M10 bolts must be used to mount the base of the U-Bracket to your vehicle. It is highly recommended that all the supplied hardware is used for the correct fitment of light.
• Before fitting stainless steel hardware, we recommend applying a small amount of anti-seize to the threads of any mounting bolts.

MODULE BREAKDOWN

To invert the bracket (according to left or right mounting positions) use the allen key provided to loosen all 4 bolts (2 on each side of the bracket and simply flip the light in accordance with whichever way is needed, and re-screw the light to the bracket using the same 4 bolts. For a more in-depth look, please refer to the YouTube installation video.

MOUNTING HARDWARE

MOUNTING LOCATION

INSTALLATION

Installation is best described within the following diagrams.

Begin by setting the light in the desired mounting position on the vehicle and roughly aiming the light within the bracket. Due to the shape of the lens, it is best to use the outer bezel as a vertical reference as to where the light will project. Keep in mind that you will need to venture out at night along a straight flat road to properly align the light.

Ensure you consider the mounting position of your light as the base bracket holes will not suit all bull bar variants. 

Depending on the install position and the available room to work with, some users may want to tighten down the position whilst access to the bolts is still accessible, however before you lock in the position, drop in the required amount of M10 bolts through the base of the bracket as certain aiming positions will obscure access to these holes.

Offer the lights bracket into the position by dropping the nuts through into your mounting platform. Achieving this next step is a little tricky but you will want to slip the washer, spring washer, and finally, the nut onto these bolts and secure tightly.

When mounting to the desired application, the order of the hardware is as follows, Bolt > Bracket > Mounting Platform > Washer > Nut

Mounting Position for Side Light

When adjusting the angle of the lights, make sure to have the bolts loose enough so that with a slight force they can be tilted & holds position but not enough so that the light swings freely. Once the ideal position is achieved, tighten all bolts firmly. If you are using the Anti-Theft Kit, please refer to the Anti-Theft diagram below for installation.

QUAD EVO Anti-Theft Kit Install

For customers that opted for the additional anti-theft kit, this is best swapped onto the light before continuing through the installation process.

The Anti-Theft kit consists of the following:

• 1 x M10 Nut Security Key
• 1 x M8 Bolt Security Key 
• 4 x 8mm Bolts (Long) - Used to secure the brackets to the sides of the QUAD EVO (fitted to the adjustment bolt position) 
• 2 x 10mm Nuts - Used to secure the bracket to the vehicle in conjunction with the included shank bolt.

QUAD EVO Cover Install

STEDI™ has designed the covers to be firm fitting. The following dictates the correct way to install the covers. Incorrect fitment may cause damage to the covers. Start by aligning the tabs on the bottom of the cover with the respective locators in the light housing. Once these are in place, press firmly down on the top of the cover until it snaps into place. Removal of the cover is as easy as placing your thumb on the top two tabs, pushing down on the tabs, and pulling out towards you.

QUAD EVO Fascia Install

The following dictates the correct way to install the colour fascia. Incorrect fitment may cause damage to the fascia or light. Removing the colour fascia requires a fascia removal key. This is included in the box with your purchase. Start by removing the cover if this hasn't been done already. In each corner of your QUAD EVO driving light, there are 4 tabs. Next to those tabs are small grooves. Simply place the end of your fascia key into these grooves and pry away to remove the fascia. To replace the colour fascia at this point, simply put the fascia into place and push on the corners one at a time until you hear it snap into place.

OPTIONAL ACCESSORIES

ANTI-THEFT:

For those wanting that little bit of extra protection, we offer a complete comprehensive anti-theft kit for that extra peace of mind having security keyed nuts and bolts ensuring a complicated time for those looking to rob you of your new driving lights.

COVERS:

Just like many of our other driving lights, customisation with covers and fascia is where we allow customers to show their individuality. The brushed stainless colour fascia that you may have seen in our Type-X™ EVO LED Driving Lights have been brought across to QUAD EVO. A selection of curated colours have been selected to cater to a wider range of modern vehicles whilst allowing matching standards to our existing line-up, for consistency of course. Each colour way will be available for both QUAD EVO centre light and QUAD EVO side light.

COLOUR FASCIAS:

Included in the box are your signature graphite grey and STEDI™ orange fascias, which have become a staple of our high-end offerings. Included in the range of available colours are blue, green, red, pink, white, and carbon fibre.